Xantech Universal Remote 686-10 Manuel d'utilisateur télécharger pdf

Remote Control Switchers

INSTALLATION INSTRUCTIONS

686-10

REMOTE SPEAKER SWITCHER

The 686-10 is an infrared remote controlled Speaker Switcher. It allows the user to turn six stereo pairs of

speakers ON and OFF by way of IR commands from a Xantech RC68+ (or RC68) Programmer. The RC68+

commands are "taught" to learning devices and passed to the 686-10 signal input terminals via Xantech IR

receivers and keypads. Individual speaker pairs may be turned on or off in any particular room or all

speakers turned on and off from any room for a "party mode".

Fig. 1 The Model 686-10 Remote Speaker Switcher

FEATURES AND SPECIFICATIONS

• 200 watts per channel capacity.

• Switchable 4-Ohm series resistor for amplifier protection.

• Seven 4-terminal plug-in connectors. One for the amplifier input and 6 for the stereo, relay-switched

speaker outputs.

• Isolated Left and Right Grounds allow use of bridging type power amplifiers.

• 4-terminal IR input for Xantech IR Receivers, SmartPads, connecting blocks and other devices.

• IR Confirm LED lights only with RC68+ On/Off, Toggle & Group IR commands.

• RC68+ IR commands permit Toggle, Pair and Group mode operations as well as different IR codes for

use of multiple 686-10's. The 686-10's Code Group number is 98.

• Universal mounting fits 19-inch racks or any 3-1/2" X 19" surface. Projects about 2-3/4 inches behind

panel with cables connected.

• Requires RC68+ Programmer (or an RC68) and 782-00 Power Supply.

• Power: 12 VDC @ 300mA.

• Dimensions: 19" W x 3-1/2" H x 2-1/4" D.

RC68 PROGRAMMER / REMOTE CONTROL

The RC68+ Programmer (available separately) contains all commands necessary to operate the 686-10

(see Fig. 2).

• You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the

Xantech Smart Pads, the 590 Controller, the 710 Fone Link, etc., with commands that operate the 686-

10.

• NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12,

ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the 686-10 are

listed. All others should be ignored.

1 2 3 4 5 6

1 2 3 4 5

PROTECTION

RESISTOR

OUT

LEFT

LEFT GND

RIGHT GND

RIGHT

12 VDC

IR CONFIRM

AMPLIFIER

INPUT

L+

L-

R-

R+

+12V

GND

IR IN

SPEAKER

REMOTE SPEAKER SWITCHER

686-10

1 2 3 4 5

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

®1Remote Control SwitchersINSTALLATION INSTRUCTIONS686-10REMOTE SPEAKER SWITCHERThe 686-10 is an infrared remote controlled Speaker Switcher. It allo

Page 2 - Fig. 2 RC68+ Programmer

®2686-10CAUTION: While the RC68+ can be used as a handheld remote control, it is highly recommended it notbe given to the final user for the followin

Page 3 - MAIN ROOM

®3Remote Control Switchers686-10Power Interruption StatusThe 686-10 should normally be plugged into an unswitched AC outlet. However, if the power to

Page 4 - IMPORTANT

®4NOTE: When the 686-10 is connected to Xantech 760-00 Match Maker room volume controls, as shownin Fig. 3, the PROTECTION RESISTOR is not necessary,

Page 5 - Remote Control Switchers

®5Remote Control Switchers1 2 3 4 5 6ON1 2 3 4 5ONPROTECTIONRESISTOROUTINLEFTLEFT GNDRIGHT GNDRIGHT12 VDCIR CONFIRMAMPLIFIERINPUTL+L-R-R++12VGNDGNDIR

Commentaires sur ces manuels

Pas de commentaire

Xantech Universal Remote 686-10 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Boîtiers de commutation en série Xantech Universal Remote 686-10. Xantech Universal Remote 686-10 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels